Toray 050-1C Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 67

background image

TORAY MBR

Instruction Manual

06-G-MB2-NHPAC-220801

24 of 61

4. Piping

The procedures of the pipe arrangement for the air diffusers and the filtrate water manifold
are described in this section. The connections of the air diffuser and the filtrate water
manifold are shown in the module drawings attached to this manual.

(1) Pipe Arrangement for the Air Diffusers

The pipe from the air supply device (blower) is connected to the two flanges (A)
located on the air diffuser (see Fig.IV-9)

. When using polypropylene diffuser, heat tolerant

plastic pipe and/or use of flexible pipe/joint is recommended for the pipe for easy flange
connection without putting stress to the air diffuser.  Also, it is recommended that the air
supply flange (B) be installed above the tank liquid level to lift the module from the tank if
necessary.
To facilitate cleaning of the air diffuser, install branch pipes and valves as illustrated in Fig.
IV-9. It is recommended that these valves be located within 500 mm above the liquid surface.
It is also highly  recommended that these valves be automatically actuated valves with
associated PLC control circuits for automatically controlled air diffuser maintenance cleaning.
Refer to VIII-2 for the procedure recommended for cleaning the air diffusers.

Fig.IV-9 Example of Piping to Air Diffuser

B

A

B

Discharge valve

Branch pipe

Air diffuser

500mm or less

Liquid level

Header pipe

A

B

«
...
27
28
29
30
31
...
»

Содержание 050-1C




































































Отзывы:

Нет отзывов

Похожие инструкции для 050-1C

Бренд: Fellowes Страницы: 20

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Бренд: SandenVendo Страницы: 19

Бренд: Zennio Страницы: 3

Бренд: Jefferson Страницы: 2

Бренд: Lighthouse Страницы: 2

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

BOMAG BW 120 AD-5

Бренд: Fayat Страницы: 210

Levitator III F-LHLEV3

Бренд: Skytron Страницы: 248

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды