Toray 050-1C Скачать руководство пользователя

Страница: 64 / 67

TORAY MBR

Instruction Manual

06-G-MB2-NHPAC-220801

59 of 61

TROUBLESHOOTING

Most of the troubles in the operation of “NHPA Series” are related to poor membrane
scouring aeration, chemical cleaning delay, and inappropriate pretreatment. The following
table lists some performance losses, their causes, and possible countermeasures.

Table X-1 Troubleshooting

Problem

Cause

Action

The air diffusion flow is below

the required level.

The blower is broken.

Stop the filtration and inspect the blower.

The air diffusers are

clogged.

Clean the air diffusers.

The air diffusion is uneven in

the module or between

modules.

The air diffusers are

clogged.

Clean the air diffusers.

The bottom of the element

block is stuck with debris.

Check the pretreatment system.

Inspect the module.

Correct operation and maintenance work

of the pretreatment system.

The filtrate water flow rate has

decreased, or the

trans-membrane pressure has

increased.

Membrane clogging has

got severe.

Conduct chemical cleaning.

Sludge is accumulated on

the membrane surface

because of uneven air

diffusion

Inspect the blower and clean the air

diffusers to improve air diffusion.
Conduct chemical cleaning.

Remove sludge cake by external

cleaning.

Abnormal properties of

sludge have worsened its

filterability.

Improve sludge properties.

・

Adjust the excess sludge discharge

rate.

・

Prevent entry of abnormal

components, such as oils.

・

Adjust the BOD load and oxygen

supply.

・

Adjust the raw water quality (add

nitrogen, phosphorous, etc.)

Air is accumulated inside

filtrate piping.

Prime the filtrate piping with water.

Install air removal equipment such as

vacuum pump.

Relocate filtrate piping.

The concentration of

suspended solids in the filtrate

water has increased.

Element and/or tube has

been broken.

Seal the element and manifold nozzle

Replace the cassette.

Leakage has occurred in

the filtrate water piping.

Inspect the faulty part

and correct the

fault.

Germs are generated on

the membrane or the filtrate

line.

To clean the filtrated water piping, inject a

sodium hypochlorite solution with an

effective chlorine concentration of 100 to

200 mg/L.

*1: Even if a cause is found in the tube, there is still the possibility of contamination inside the element. Thus,

seal the element and manifold nozzle.

*2: To check the piping joints and welds for leakage with a pressure being applied, be careful not to apply

pressure to the membrane modules.

Содержание 050-1C




































































Результаты поиска

Содержание 050-1C

Отзывы:

Похожие инструкции для 050-1C

Бренды по названию

Популярные бренды

Toray 050-1C, Инструкция по эксплуатации

Результаты поиска

Содержание 050-1C

Отзывы:

Похожие инструкции для 050-1C

Бренды по названию

Популярные бренды