Toray 050-1C Скачать руководство пользователя страница 2

Страница: 2 / 67

Instruction Manual

Toray MBR

06-G-MB2-NHPAC-220801

Notice

The data and information contained in this document are based upon rigorous technical

testing by Toray, and is to the best of our knowledge reliable. Toray cannot control design

and operating conditions, and consequently Toray does not assume any liability for results

obtained or damage incurred through the application of the information provided herein.

No liability, warranty or guarantee of final product performance by Toray is implied by the

information provided in this document.

This manual supersedes all previous versions. Technical modification of products or

production technology may necessitate changes to information in this manual without prior

notice. Please verify that your version of the manual is the latest version available by either

contacting Toray, or checking online at

www.water.toray

Terms and Conditions of Use
When using this document, please read the Terms and Conditions of Use below thoroughly and agree to them before using

this document. By using this document, you agree to all of the Terms and Conditions of Use outlined here. The Terms and

Conditions of Use are subject to change without prior notice, so please check with Toray for the latest Terms and Conditions

of Use before using the document.

1. Intellectual Property Rights

The content in this document is protected by copyright laws in respective countries and relevant treaties. Accordingly,

the document's information may not be reproduced, altered, or distributed without permission in writing from Toray. We

permit downloading this document through Toray's website as a PDF file, stored on a personal computer, and printed

out for customers' personal use. However, we prohibit transferring this document to any other websites or printed media.

The material contained in this document may not be used without permission from the copyright holder for any other

purpose that exceeds the scope permitted under copyright law.

2. Trademarks

The "TORAY" company name used in this document is a trade name, and the names of products manufactured by

Toray are trademarks or registered trademarks. Toray's trade names and trademarks are protected under the Japanese

Trademark Law, the Unfair Competition Prevention Law, and other legislation. The trade name and trademarks may not

be used or reproduced without express permission from Toray.

3. Disclaimer

Toray takes all reasonable care in updating the information in this document. However, Toray makes no representation

and warranty of any kind, either express or implied, including without limitation, any implied warranties concerning the

accuracy, usefulness, suitability, or fitness for a particular purpose of the information in the document.

Toray shall not be responsible or liable for any losses or damage incurred due to the use of the information in this

document. The information in this document is subject to change without prior notice, and Toray reserves the right to

suspend or discontinue the publication of this document.

4. Availability of Goods and Services

The goods and services contained in this document are not available in all countries and regions. Goods and services

may also be supplied under different trademarks in different countries. We ask that you contact your nearest Toray

representative office if you wish to use the goods and services shown or implied in this document.

5. Proper Law and Court of Jurisdiction

This Terms and Conditions of Use shall be governed by and construed according to the laws of Japan. Any and all

disputes arising out of or relating to this document shall be brought to the Tokyo District Court Tokyo, Japan.

Содержание 050-1C




































































Результаты поиска

Содержание 050-1C

Отзывы:

Похожие инструкции для 050-1C

Бренды по названию

Популярные бренды

Toray 050-1C, Инструкция по эксплуатации

Результаты поиска

Содержание 050-1C

Отзывы:

Похожие инструкции для 050-1C

Бренды по названию

Популярные бренды