Toray 050-1C Скачать руководство пользователя | Manualshive

Страница: 39 / 67

background image

TORAY MBR

Instruction Manual

06-G-MB2-NHPAC-220801

34 of 61

c. Check the system controls and associated control components for proper operation

and proper sequence of operation.

d. Start the clean water filtration process. At the initial operation of suction pump,

priming (filling the suction piping with water) may be needed for proper pump
suction and in that case avoid pressurizing the filtrate side of "NHPA Series” over
10kPa. Measure and record the trans-membrane pressure and water temperature at
designed filtration rates (

at normal, maximum, and minimum flow rates

). It is

beneficial to periodically record flow rates and TMP values.

e. Stop the clean water filtration process and discontinue the air supply as soon as the

above tests have been satisfactorily completed.

White foaming may occur in the membrane tank during clean water

operation. The foaming is caused by the leaching of residual

biodegradable hydrophilic components contained in the membrane

after the manufacturing process. Foaming is normal and does not

adversely affect the membrane filtration process but if you want to

remove this, do not use silicone-based anti-foaming agent which

may cause choking of membrane pores.

Do not conduct clean water operation for a long time. Clean water

operation may cause membrane clogging.

Keep the membranes wet once they get wet. If the membranes are

allowed to dry out, the permeability of the membranes may be

permanently reduced.

Avoid pressurizing the filtrate side of "NHPA Series” over 10 kPa.

2. Seeding Sludge Injection

Do not attempt to produce filtrate from any wastewater that has not first been seeded with
activated sludge. Failure to do so will result in severe clogging of the membrane pores
Follow these steps when seeding sludge in the membrane tank with activated sludge:

(1)

Locate a nearby wastewater treatment facility that treats wastewater similar in
composition to the wastewater to be treated with the new “NHPA Series”. Make
arrangements to transport some of that healthy, activated sludge from the nearby
wastewater facility to the facility needing the seeding sludge. Activated sludge
with higher MLSS concentration and higher MLVSS/MLSS ratio is preferable.

Initial MLSS concentration of the membrane tank should be at least 3,000
mg/L or higher. Higher than 7,000 mg/L is preferred.

(2)

Supply the seeding sludge through the <3mm screen to the tank.

(3)

Begin feeding the raw wastewater as soon as possible after the activated sludge
has been introduced into the membrane tank.

(4) Do not use seeding agents.

CAUTION

!

CAUTION

!

CAUTION

!

CAUTION

!

«
...
37
38
39
40
41
...
»

Содержание 050-1C




































































Отзывы:

Нет отзывов

Похожие инструкции для 050-1C

Бренд: Qingdao H.Y Страницы: 6

Бренд: Parker Страницы: 54

Бренд: Keithley Страницы: 149

Бренд: GE Страницы: 138

Бренд: York Fitness Страницы: 34

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: idiag Страницы: 12

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды