Toray 050-1C Скачать руководство пользователя | Manualshive

Страница: 43 / 67

background image

TORAY MBR

Instruction Manual

06-G-MB2-NHPAC-220801

38 of 61

2. Operating Parameters

The  performance  of  the “NHPA  Series”  varies  depending on raw water quality  and  site
specific operating conditions.  In order to achieve stable “NHPA  Series” operation,  it  is
recommended that various operating parameter values be monitored and recorded regularly.
The following operational parameter values should be recorded regularly.

(1)

Scouring air flow rate (blower air flow)

(2)

Diffusion pressure (blower discharge pressure)

(3)

Filtrate water flow rate

(4)

Trans-membrane pressure (TMP)

(5)

Liquid temperature in the membrane tank

(6)

DO (dissolved oxygen) concentration in the membrane tank

(7)

pH in the membrane tank

(8)

MLSS in the membrane tank

(9)

Raw water quality (BOD, COD, turbidity, T-N, T-P, etc.)

(10)  Filtrate water quality (BOD, COD, turbidity, T-N, T-P, TSS etc.)
(11)  Excess-sludge discharge rate
(12)  Sludge viscosity
(13)  Sludge filterability

Preferable recording frequencies are;



Every five (5) minutes for on-line instruments



Every day for off-line instruments and sludge properties



Every week for water quality analysis

3. Basic Control Philosophy

Presented below is the point of the generic MBR control philosophy. The actual MBR system
control philosophy will be based on the specific site operating conditions.
(1)

Suction Pump

: The filtrate suction pump should be controlled to operate for intervals of

nine (9) minutes on and one  (1) minute off. The filtrate suction pump motor should be
fitted with a VFD drive. A filtrate flow transmitter should be installed to provide a control
signal to the suction pump VFD. The suction pump should be stopped if the liquid level in
the  membrane  tank drops to a predetermined low liquid level. If, at any time, the air
supply to the membrane  module  or RAS (return activated sludge)  is interrupted,  the
suction pump should be stopped. Do not operate the filtrate  suction pump on low
membrane tank level or high TMP. Once the air supply has been restored the membrane
tank and good RAS circulation is observed, delay the activation of the suction pump for
one minute to make certain sufficient sludge mixing has taken place prior to restarting the
filtration process. The suction pump should always be off when performing air diffuser
cleaning.

«
...
41
42
43
44
45
...
»

Содержание 050-1C




































































Отзывы:

Нет отзывов

Похожие инструкции для 050-1C

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Panlux Страницы: 2

Бренд: d.s.f. Страницы: 8

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: VADDIO Страницы: 58

Бренд: B-K lighting Страницы: 2

Бренд: JBM Страницы: 13

So-exercise TX7

Бренд: T-SoX Страницы: 8

Бренд: ADJ Страницы: 6

Бренд: BERRIDGE Страницы: 11

Бренд: Helmer Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды