manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 60

58

Laser Beam (Downward)

Perform the following check after completing "Vertical Calibration (Upward)" on the previous 
page.

Checking

1

Place a piece of paper on each wall and mea-
sure the datum position in the same manner as 
" Vertical Calibration (Upward)" .

2

Set the laser on its floor mount, with the head 
facing wall B.
Turn the leveling screw to bring the bubble to 
the center of the vertical level vial.

3

Turn the power switch on.

4

Measure the distance from datum position on 
wall A.

5

Turn the power switch off. Rotate the instrument 
180 degrees with the rotary head facing wall A.
(do not move the front floor mount leg)
Turn the power switch on again and level the 
instrument.

6

Measure the distance from datum position on wall B.

7

When the difference between measurements is less than 2.5mm, the laser position is pre-
cise enough.

 

about 5 m 

Wall

 

A

Wall 

B

10 cm

Datum position

Datum position

Note; If difference exceeds 2.5 mm, contact your dealer or Topcon.

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды