manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 29

27

Height Alert function

When auto-leveling is active, this function prevents the instrument from operating if it is dis-
turbed. This insures accurate control. If the unit is disturbed, the elevation should be verified
and reestablished if necessary.

1

 To activate the height alert function, depress and hold the left of arrow keys (X2) (see 

page 17 ) on the control panel while turning on the instrument by pressing the Power con-
trol pad. 

2

 When this function is active and the unit is disturbed, visible LEDs will rapidly flash. 

3

To re-activate auto-leveling and check the beam height, turn the unit off, then on again by 

pressing the Power control pad twice. After auto-leveling is complete, check the beam 
height to confirm it has not changed. 

4

The Height Alert function is now inactive. To re-activate, turn unit off and repeat step 1.

High Power Mode (RL-VH3G Only)

Pressing the high power mode key, the laser power will change alternately.

LED

Note: When the instrument is in Scanning, Auto grade or Auto-line control mode, it is not possible 

to use High power mode.

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды