manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 54

52

Horizontal Rotation Cone Error

Perform the following check after completing "Horizontal Calibration" on the previous page.

1

Set up the laser centered between two walls approximately 40m (131ft) apart. Orient the 
instrument so one axis, either X or Y, is facing the walls. 

2

Locate and mark the position of the rotating laser beam on both walls using the target.

3

Turn off the instrument and move the instrument closer to wall A (1m to 2m /3 ft to 6 ft).
Do not change the axis orientation of the instrument. Turn the instrument on.

4

Again locate and mark the position of the rotating laser beam on both walls using the tar-
get.

5

Measure the distance between the first and second marks on each wall.

6

If the difference between each set of marks is less than 4mm (5/32 of an inch), no error 

exists.

Note

• If the error is greater than 4mm ( 5/32 of an inch), contact your Topcon dealer.

∞ 

∞ 

Cone error

Datum position

Wall 

Wall 

B

A

Wall 

A

Wall 

B

Minimum about 40m/131ft

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды