Topcon RL-VH3A Скачать руководство пользователя страница 48

Страница: 48 / 75

Charging

Plug the AC/DC converter (AD-9B or AD-7C)
into the DB-49C battery holder.

Insert the converter receptacle in an outlet
(AD-9B is for AC120V, AD-7C is for AC230V)

Complete charging by unplugging the con-
verter connector from the DB-49C battery
holder after approximately 9 hours.

Unplug the converter receptacle from the out-
let.

The DB-49C LED will indicate charging status;

Red ON

: Charging.

Green ON

: Charging completed.

Green flashing : DB-49C is not connected to

BT-49Q.

Red flashing

: BT-49Q protection feature is

working automatically.

RL-VH3A/B/G can be used
in this state.

Automatic protection feature; In case of overcharge or high or low temperature state exceeding
charging range, charging will be stopped or changed to protect battery.

DB-49C

AC/DC converter
AD-9B/7C

BT-49Q

DB-49C

Содержание RL-VH3A












































































Результаты поиска

Содержание RL-VH3A

Отзывы:

Бренды по названию

Популярные бренды

Topcon RL-VH3A, Инструкция по эксплуатации

Результаты поиска

Содержание RL-VH3A

Отзывы:

Бренды по названию

Популярные бренды