manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 3

 

1

Foreword

Thank you for purchasing the Topcon RL-VH3G/A/B Rotating Laser.

It is one the world’s most advanced lasers. 

To quickly and effectively use the RL-VH3G/A/B, please read these brief 

instructions carefully, and keep them in a convenient location for future refer-

ence.

Handling Precautions

1 Vibration and Impact Protection

When transporting the instrument, provide protection to minimize risk of severe vibration 
or impact. Severe vibration or impacts may affect beam accuracy.

2. Laser Scanning Interference

Particular reflective surfaces such as mirrors and some glass surfaces, can cause beam 
reflection that in very rare circumstances can interfere with the laser scanning function. If 
this should happen, simply change the location of the laser or cover the reflective surface.

Caution:

Use of adjustment controls or performance procedures other than those specified herein 
may results in hazardous radiation exposure.

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды