manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 56

54

7

Compare the two measurements dHa and dHb. If the difference between the two mea-
surements is less than 2.5mm ( 1/10 of an inch), no adjustment is necessary. Otherwise, 

adjust as follows.

(2)Checking RL-VH3B

1

Set up the instrument half way between 2 walls a minimum of 40m away from each other. 
(The instrument can be facing either direction X or Y. And no tripod is used.)

2

Turn the power switch on.

3

Place a piece of paper on each wall (A 
and B).
Mark the horizontal laser positions (Ma 
and Mb) on each wall using target.

4

Turn the power switch off. Position the 
instrument for vertical operation (see 
instruction on page 19 ) with the rotary 
side directly facing wall A (see illustra-
tion). Make sure the unit is level by check-
ing the circular level vial. Use the leveling 
screw to adjust if necessary.

5

Turn the power switch on. (Laser beam 
should be in scanning mode.)

6

Mark where the split beam emitted from 
the top of the rotary head strikes wall A (Ha). Measure the distance (dHa) between marks 
Ma and Ha.

about 40 m (131ft) 

Wall

 

A

Wall

 

B

about 1m

Foot

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды