manualshive.com logo in svg

Topcon RL-VH3A, Инструкция по эксплуатации

Поделиться
Скачать
Topcon RL-VH3A Скачать руководство пользователя страница 22

20

Battery Warning Indicator

The Battery warning indicator will be shown for several minutes when the instrument is pow-

ered ON or when the battery level changes.

Auto-leveling lamp

Flashing : Auto-leveling is in process. When automatic is leveling almost complete, the

flashing rate will be slow. The head will not rotate and the laser beam will not
emit during the auto-leveling process.

ON Solid: Auto-leveling is complete.

The rotary head is active and emits the laser beam.

To turn automatic leveling off

Note

• When BT-49Q is used, the blinking period will be short because of the charac-

teristic of the battery.

• Laser sensor LS-70A/B can detect low power state of laser.

Battery is sufficient.

Dead batteries. Recharge the battery or replace the dry batteries with new 
ones.(The laser will turn completely off after blinking for about five minutes.)
NOTE:Even if an AC/DC converter is connected at this time, blinking still con-
tinues. Once the power is turned off, the battery remaining display will reset.

Continuous

Blinking

Blinking order

The power is low, but laser is still usable. (Blinking continues until batteries are 
dead.)

Содержание RL-VH3A












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды