background image

WARRANTY.....

Top Flite Models guarantees this kit to be free of defects in both material and workmanship at the date of purchase. This warranty does

not cover any component parts damaged by use or modification. In no case shall Top Flite‘s liability exceed the original cost of the purchased kit. Further, Top Flite reserves

the right to change or modify this warranty without notice. In that Top Flite has no control over the final assembly or material used for final assembly, no liability shall be assumed

nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product the user accepts all resulting

liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to immediately return this kit in new and unused

condition to the place of purchase.

Top Flite Models   P.O. Box 788   Urbana, Il  61803                  

Technical Assistance Call (217)398-8970   [email protected]

READ THROUGH THIS INSTRUCTION BOOK FIRST. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

USA

MADE IN 

T349P03  for  TOPA0160 V1.0

Entire Contents © Copyright 2002

Wingspan:

80 in [2032 mm]

Wing Area:

1025 sq in [66.1 sq dm]

Weight:

10 to 14 lb [4536 – 6350 g]

Wing Loading:

22.5 to 31.5 oz/sq ft    

[68.7 – 96.1 g/sq dm]

Fuselage Length:

62.8 in [1595 mm]

Содержание T-34B MENTOR



































































Отзывы: