background image

Biplane

RC-37 INSTRUCTION MANUAL

INTRODUCTION

The Elder Biplane is the third
design based on the popular
Elder-series of models. This
design is a direct result of popular
demand and it surely is the

largest model of the three. Your

Elder Biplane packs a huge wing

area of 1492 square inches, that's
10.3 square feet of lifting surface!

This means that when the model

is built within the expected

weight range of 7-1/2-8-1/2 pounds,
the resulting wing loading range
would be 11.6 - 13.1 ounces per
square foot! It also means that if

you went with the heaviest engine
available and went crazy in the

detailing and finishing aspects of this model and manag-

ed to get the weight up to 10 pounds, the wing loading
would still only be 15.4 ounces per square foot!

All of the above allows your Elder Biplane to be powered

by a very wide range of engines. This design has been

tested quite successfully using 2-stroke engines as small
as .45 and on up to .75's. For 4-stroke work, we suggest

engine sizes of .60 to .90 in displacement. Like its smaller
counterparts, the real "kick" of this design is its extreme-

ly realistic flight characteristics. Slow fly-bys are breath-

taking without the fear of losing aileron authority. Land-
ings and take-offs are absolutely effortless. In the airyour

Elder Biplane is fully capable of some of the most realistic

aerobatics you've ever seen! You can expect beautiful

loops, stall turns and snap rolls, all at speeds that actual-
ly allow you to watch the airplane instead of a "blur".

Your Elder Biplane is a rugged design that will operate

very nicely out of dirt, grass or paved flying fields. The uni-
que, shock-absorbing landing gear, proto-typical of the

Elders era, really works to smooth out even the bumpiest

of fields. With its thick airfoil section and generous wing
area, your Elder Biplane will not tend to build-up ex-
cessive airspeed. This characteristic keeps the relative

inertia low and means that crash damage is kept to a

minimum.

Like otherEIders, the Elder Biplane lends itself to all kinds

of detailing, if you're so inclined. For the beginner,
nothing fancy is needed; just fly it and enjoy. For the
builder with an imagination, the Elder Biplane can be
detailed to such a degree that other pilots at your field will
swear the airplane is a scale model! In the COVERING &
FINISHING section of these instructions there are some
ideas for detailing that might be of interest, please take

the time to read them.

TOP FLITE MODELS INC.

2635 S. WABASH AVENUE • CHICAGO, ILLINOIS 60616

Содержание Elder Biplane RC-37





















Отзывы: