Tone Commander 6210 Скачать руководство пользователя

Страница: 11 / 86

Tone Commander 6210/6220 User Manual

Bridging a Shared Call Appearance ________

You can bridge (connect to) an active call on a call appearance that is
shared with other terminals, unless call privacy is enabled at the
network.

Press the busy Call Appearance key for the call you want to
bridge.

Lift the handset or press the

Spkr

key.

The call duration timer begins when you are connected to the
call.

To disconnect from the call, replace the handset or press the

Spkr

key. The other parties will remain connected.

Displaying Call Appearance Information ____

Press the

Call

key.

Select ID

(Shortcut – you can skip this step and immediately

press Call Appearance keys)

Press Call Appearance keys.
Network call information will be displayed for currently active
keys.
"NO CALL INFORMATION" and the assigned directory
number, if available, will be displayed for idle keys.

Press the

Call

Done

key when finished.

Holding Calls ___________________________

Press the

Hold

key or another Call Appearance key to place

the currently connected call on hold.
The held call appearance indicator will wink with a green light.

Press the held Call Appearance key to return to the call.

Call

Done

Содержание 6210























































































Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды

Tone Commander 6210, Руководство пользователя

Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды