Tone Commander 6210 Скачать руководство пользователя | Manualshive

Страница: 19 / 86

background image

16

Tone Commander 6210/6220 User Manual

Using Voice Announce ___________________

The Voice Announce feature may be used to provide hands-free call
announcing of screened calls or station-level paging when your phone
is on-hook. Incoming calls that meet specific predefined criteria (see
page 40) can be answered automatically by the speakerphone. The
microphone can be automatically disabled for announcing only, or
enabled to allow two-way conversations. You can enable or disable
Voice Announce at any time.

Enabling/Disabling

When the phone is idle, the display will show the current Voice
Announce state.

The Voice Announce state is shown only if Voice Announce
keys have been set up as explained on page 40

.

Press the softkey beneath the VA display to enable or disable
Voice Announce.

Receiving Voice Announce Calls

Calls selected for voice announcing will be answered automatically.
You and the caller will hear a double beep if your microphone is muted,
or a single beep if your microphone is enabled. The call will disconnect
when the caller hangs up. After the call has been answered, you can
pick up the handset for a private conversation, turn muting on or off,
press the

Spkr

key to disconnect, and perform other normal call

operations.

Voice Announce is disabled when you are on an active

call with the handset, headset, or speakerphone

.

CAUTION

– If Call Announce is enabled for a calling directory number,

the caller should not transfer calls unscreened (blind) to your
telephone, otherwise the transferred call will be answered using Voice
Announce.

UNANS

VA ON

«
...
17
18
19
20
21
...
»

Содержание 6210























































































Отзывы:

Нет отзывов

Похожие инструкции для 6210

Бренд: D-Link Страницы: 58

Бренд: AT&T Страницы: 32

Бренд: Curtis Страницы: 4

Gigaset CX100 isdn

Бренд: Gigaset Страницы: 123

Бренд: JabloCom Страницы: 2

Бренд: BT Страницы: 2

Бренд: Matosio Страницы: 37

Бренд: Aastra Страницы: 113

Бренд: BELGACOM Страницы: 32

Бренд: NEC Страницы: 16

Бренд: NEC Страницы: 52

Бренд: NEC Страницы: 100

Бренд: NEC Страницы: 222

Бренд: NEC Страницы: 258

UNIVERGE UM8500

Бренд: NEC Страницы: 352

PAYPHONE ZIRCON

Бренд: Doro Страницы: 41

Бренд: Swyx Страницы: 3

Бренд: switel Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды