Tone Commander 6210 Скачать руководство пользователя страница 13

Страница: 13 / 86

Tone Commander 6210/6220 User Manual

Conferencing a Held Call

Press the

Conf

key while you are on an active call with

another call on hold.
The current call is placed on hold and an idle call appearance
is automatically selected. The

Conf

indicator lights.

Press the Call Appearance key for the held call you wish to
add to the conference.

Press the

Conf

key to conference all parties together.

Repeat the above steps to add another party.

Dropping the Last Party

Press the

Drop

key to remove the last party added to a

conference.

Terminating a Conference

Replace the handset or press the

Spkr

key to terminate a

conference, removing yourself and all other parties.

Depending on your network configuration, other parties in the
conference may remain connected or be disconnected.

Using Network Features __________________

Feature Activator keys access features provided by the telephone
network. A feature is active when the key’s red indicator is on.

Some commonly available features are listed below. Consult your
service provider for more information.

Call Forwarding

Forwards ringing calls to another number. When the Call Forward key
indicator is lit, incoming calls will be forwarded.

Содержание 6210























































































Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды

Tone Commander 6210, Руководство пользователя

Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды