Tone Commander 6210 Скачать руководство пользователя

Страница: 66 / 86

Tone Commander 6210/6220 User Manual

Receive (handset and headset)

Select RCV- or RCV+ to adjust the receiver volume level.
The new setting will be shown in the display.

Transmit (headset only)

Select VOICE.

Select XMT- or XMT+ to adjust the headset’s transmit volume
level.
The new setting will be shown in the display.

Press the

Done

key to return to the Voice Mode menu or the

Setup

key to exit Setup Mode.

Adjusting the Display Contrast ____________

This setting adjusts the contrast of the display to compensate for
viewing position and lighting conditions. You can also tilt the display for
best visibility.

From the User Options menu, select DISPLY.
(

Setup

→

USER

→

More

→

DISPLY)

Select (

) to lighten the display (less contrast), or (

) to

darken the display (more contrast).
The display contrast will change, and a bar graph will show
the new contrast setting.

Press the

Done

key to return to the User Options menu or the

Setup

key to exit Setup Mode.

Done

CONTRAST [{{{{{ ]
(-) (+)

Done

Содержание 6210























































































Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды

Tone Commander 6210, Руководство пользователя

Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды