Tone Commander 6210 Скачать руководство пользователя

Страница: 12 / 86

Tone Commander 6210/6220 User Manual

Transferring Calls _______________________

Use this feature to transfer an active call to another party.

Press the

Tran

key while in an active call.

The current call is placed on hold, and an idle call appearance
is automatically selected. The

Tran

indicator flashes (on some

network switch types, the

Conf

indicator may light instead of

the

Tran

indicator).

Dial the party you want to transfer the call to with the dial pad
or a Speed Dial key.
Wait until the called party answers to announce the call, or
transfer it immediately before the called party answers.

Press the

Tran

key again to transfer the call.

DSS Transfer

While on an active call, press the

Tran

key.

Press the DSS key for the destination party.

Press the

Tran

key to transfer the call.

Conferencing Calls ______________________

You can initiate multi-party conference calls. Conferences are limited to
3 or 6 parties, depending on your network configuration.

Conferencing a New Call

Press the

Conf

key while on an active call.

The current call is placed on hold and an idle call appearance
is automatically selected. The

Conf

indicator lights.

Dial the party you wish to add to the conference.

After the added party answers, press the

Conf

key to

conference all parties together.

Repeat the above steps to add another party.

Содержание 6210























































































Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды

Tone Commander 6210, Руководство пользователя

Результаты поиска

Содержание 6210

Отзывы:

Похожие инструкции для 6210

Бренды по названию

Популярные бренды