Toku TNB-08M Скачать руководство пользователя

Страница: 94 / 133

3-7-3

REFILLING OF NITROGEN GAS

Fit a pressure regulator (2) and hose (3)

onto the nitrogen gas cylinder (1)

Fit a filling adapter (4) to the end of the

hose and insert the adapter into the gas

valve

Open the regulator valve (B) of the

nitrogen gas cylinder

Turn the handle (A) of the pressure

regulator (2) while reading the pressure

gauge of the regulator. Fill with nitrogen

gas up to the pressure shown in the table

Stop turning the handle (A) after the gas

pressure reaches the correct value shown

in the table and keep it there for about 10

seconds.

Make sure the pressure regulator handle (A) is loosened.

When refilling the nitrogen gas, make sure the hydraulic breaker is cooled off.

CAUTION

WARNING

Do not use any other gas except nitrogen gas.

In other gases are used, it may explode and is dangerous.

WARNING

It does not perform the replenishment of nitrogen gas immediately after operation.

Since each unit is hot, it is possible to burn. Please perform the work from the cold is always

oil and various parts.

Содержание TNB-08M





































































































































Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды

Toku TNB-08M, Руководство пользователя

Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды