Toku TNB-08M Скачать руководство пользователя

Страница: 45 / 133

2-12. OPERATION OF HYDRAULIC BREAKER

⚫

The hydraulic breaker is an attachment to the hydraulic excavator. Follow the instruction

manual for the hydraulic excavator when starting the machine.

⚫

Set up the excavator to operate the hydraulic breaker. If there is a “Hydraulic Breaker

Mode” on the excavator, change to the mode. Position the throttle of the excavator

(engine RPM) at the mark for the hydraulic breaker.

Then, follow the excavator manual for operation.

⚫

Place the breaker against the object at a

90-degree angle.

⚫

When operating the breaker, raise the chisel

against the object and the front portion of

the excavator about 5 cm (2 inch) from the

ground.

⚫

When operating the hydraulic breaker, ensure to use the piping for the hydraulic breaker.

⚫

If there is a ”Hydraulic Breaker Mode” on the excavator, change to the mode.

⚫

If a piping of the excavator is set up for the hydraulic crusher, 1) the excessive hydraulic

oil might be supplied to the hydraulic breaker. 2) Wrong pedaling creates the high pressure

to the low pressure piping of the hydraulic breaker. In both cases, it could cause damage

to the hydraulic breaker.

CAUTION

When the angle is not 90 degree, the breaker will

be slipped. It cause the chisel breakage, seizure of

bush. Choose stable surface to beating. Avoid

any excessive force.

CAUTION

When pushing force is not enough, it will lead

blank blows. Blank blows will give a big impact to

the breaker and excavator, and cause serious

damage and the breakdown.

CAUTION

Ensure that the front part of the excavator is not raised too high.

After the material is broken, take caution since the balance of the excavator becomes unstable.

Содержание TNB-08M





































































































































Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды

Toku TNB-08M, Руководство пользователя

Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды