Toku TNB-08M Скачать руководство пользователя

Страница: 107 / 133

103

3-9.

REPLACEMENT OF OIL FILTER ELEMENT

⚫

Replace the filter element of the oil filter, which is located on the breaker piping line every

100 hours. In case it is not available on the breaker piping line replace the filter element of

the filter every 100 hours in the tank or close to the tank.

3-10.

CHANGE THE HYDRAULIC OIL IN THE TANK

⚫

Carefully read the manual of the excavator and change the hydraulic oil every 600 hrs in

the tank of an excavator.

⚫

As the hydraulic oil is constantly under the harsh conditions such as high temperature and

high pressure it deteriorates along with time. The designated periodic oil change is obliged

even though it is not contaminated.

⚫

The hydraulic oil is like the blood of human being for machines, therefore it must pay

attention not to get mix the impure substance like water, metal particle and dirt into the oil.

⚫

Fill the oil at designated amount. The oil amount should be exact; otherwise the excessive

or less oil amount causes the failure of a breaker and an excavator.

Various parts will be very hot after operation of the engine. Do not change the filter element

immediately. Change the element after the hydraulic oil and various parts have cooled off.

WARNING

Various parts will be very hot after operation of the engine. Do not change the hydraulic

oil immediately. You can get burn. Change the oil after the hydraulic oil and various parts

have cooled off.

WARNING

Содержание TNB-08M





































































































































Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды

Toku TNB-08M, Руководство пользователя

Результаты поиска

Содержание TNB-08M

Отзывы:

Похожие инструкции для TNB-08M

Бренды по названию

Популярные бренды