manualshive.com logo in svg

TOHATSU MFS 115A, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 115A Скачать руководство пользователя страница 92

EMISSION CONTROL SYSTEM INFORMATION

102

14

ENOM01005-0

Problems that can affect emission

If you notice any of the following symp-
t o m s,   h a v e   y o ur   o u t b o a r d   m o t o r
inspected and repaired by an authorized
Tohatsu service dealer before further
use.

z

Hard starting or stalling immediately
after starting

z

Rough idling

z

Misfiring/backfiring under load

z

Afterburning (backfiring)

z

Black exhaust smoke or increased fuel
consumption

ENOM01006-0

Replacement Parts

The emission control system in your
Tohat su  ou t board  mo tor  has  be en
designed, built, and certified to conform
with the EPA and California emission reg-
ulations. Whenever requesting mainte-
nance, use of Tohatsu Genuine parts is
highly recommended. Tohatsu Genuine
parts constitute replacement parts man-
ufactured to the same high standards as
the original par ts, thus guaranteeing
uninterrupted high performance of your
outboard motor. The use of replacement
parts other than Tohatsu Genuine parts
could jeopardize the effectiveness of the
emission control system.

Tohatsu, as a manufacturer of aftermar-
ket parts, assumes the responsibility that
replacement par ts will not adversely
affect emission performance. The manu-
facturer or rebuilder of the replacements

parts must certify that use of the parts
will not result in a failure of the engine to
comply with these regulations.

ENOM00033-0

.

EQUIPPED FOR UNITED STATES AND 
CANADA MODEL

Required for outboards manufactured
for sale, sold, or offered for sale in the
United States.

z

TOHATSU  engine  has  used  fuel  hoses
for The Environmental Protection
Agency (EPA) requires from January 1,
2011.

Low permeation fuel hose 
requirement

Содержание MFS 115A

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды