manualshive.com logo in svg

TOHATSU MFS 115A, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 115A Скачать руководство пользователя страница 33

PRE-OPERATING PREPARATIONS

33

6

Remedy

1.

Reduce the throttle to less than half
opening,  and  move  to  safe  place
quickly, and stop the engine. 

Check the propeller for bent or dam-
aged blades. 

Consult an authorized dealer if engine
shows the same result even after
replacing propeller with new one.

2.

Move  to  safe  place  quickly,  and  stop
the engine. 

Check the engine oil level, and add
engine oil if necessary. 

Consult  your  dealer  if  the  engine  oil
level is too low or too high.

3.

Move to safe place quickly, and check
the discharge of cooling water from
the water check port at idle speed
and stop engine. 

Remove any foreign matter on the
gear case and propeller if necessary.
Consult an authorized dealer if no
discharge of cooling water.

4.

Consult an authorized dealer.

5.

Replace the engine oil and reset the
indicator.

Содержание MFS 115A

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды