TOHATSU MFS 115A Скачать руководство пользователя страница 28

Страница: 28 / 96

PRE-OPERATING PREPARATIONS

1. Fully open the air vent screw on the

fuel tank cap and release internal
pressure.

Air vent screw

Fuel tank cap

2. Open the fuel tank cap slowly.

3. Fill the fuel carefully not to over flow.

4. After filling the tank, close the fuel

tank cap.

ENOM00037-A

ENOW00022-1

The engine oil is drained for shipping from
the factory. Be sure to fill the engine to the
proper level before starting engine.

ENOW00092-A

Do not overfill engine oil, or engine oil
could leak and/or engine could be dam-
aged. If engine oil level is over upper limit
marks of oil gauge, drain oil to level lower
than upper limit.

Be sure that outboard motor is in upright
and level position when che cking or
changing oil.

Stop engine immediately if low oil pres-
sure warning lamp is lit or oil leak is found,
or engine could be severely damaged.
Consult dealer.

Wipe off engine oil well immediately if
spilled and dispose of it in accordance
with local fire prevention and environ-
ment protection regulations.

ENOM01812-B

1. Place the outboard motor in a verti-

cal position.

2. Turn the top cowl hook levers to

unlock, lift and remove the top cowl.

Cowl hook lever

3. Engine oil filling

CAUTION

ENOF00029-0

SAFE FILL

LEVEL

25 L

NIVEAU

MAXIMUM

ENOF00030-A

CAUTION

ENOF02435-0

ENOF02436-0

Содержание MFS 115A

































































































Результаты поиска

Содержание MFS 115A

Отзывы:

Бренды по названию

Популярные бренды

TOHATSU MFS 115A, Руководство пользователя

Результаты поиска

Содержание MFS 115A

Отзывы:

Бренды по названию

Популярные бренды