TOHATSU MFS 115A Скачать руководство пользователя страница 41

Страница: 41 / 96

ENGINE OPERATION

ENOM01807-0

Side mount RC type

1. Be sure to install the stop switch lock

to the stop switch, and attach the
stop switch lanyard securely to the
operator or to the operator's PFD
(Personal Flotation Device.)

Stop switch lock

2. Insert the main switch key.

3. Set the control lever in the Neutral

position. Do not raise the free throt-
tle lever when starting the engine.

Neutral (N)

Control lever

Fully opened (Forward)

Fully opened (Reverse)

Free throttle lever

Main switch key

Stop switch

4. Turn the main switch key to ON posi-

tion and confirm three warning lamps
light up with buzzer sound and then
go off.

Warning lamp

5. Turn the main switch key to the START

position and release it to start the
engine. The engine will crank continu-
ously until the engine starts.

ENON00942-0

Note

It takes maximum 4 seconds of the
continuous crank before the engine
starts.

If fail to start the engine, crank again
after 10 seconds or more.

START

OFF

ENON00035-A

Note

The free throttle lever can not be raised
when the control lever shift is in Forward
or Reverse.

ENOF00869-1

ENOF00870-1

ENOF00851-A

ENOF00871-1

Содержание MFS 115A

































































































Результаты поиска

Содержание MFS 115A

Отзывы:

Бренды по названию

Популярные бренды

TOHATSU MFS 115A, Руководство пользователя

Результаты поиска

Содержание MFS 115A

Отзывы:

Бренды по названию

Популярные бренды