manualshive.com logo in svg

TOHATSU MFS 115A, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 115A Скачать руководство пользователя страница 54

ENGINE OPERATION

54

7

ENOM00060-A

ENOW00055-0

Do not tilt up or down outboard motor when
swimmer(s) or passenger is near to prevent
them from being caught between outboard
motor body and clamp bracket in case the
outboard motor body falls.

ENOW00048-0

When tilting up or down, be careful not to
place your hand between the swivel bracket
and the stern bracket.
Be sure to tilt the outboard motor down
slowly.

ENOW00056-A

When tilting up outboard motor with fuel
joint for over a few minutes, be sure to dis-
connect fuel hose, or fuel may leak, poten-
tially catching fire.

ENOW00057-0

Do not tilt up outboard motor while engine
operates, or no cooling water may be fed,
leading to engine seizure due to overheating.

ENON00921-0

Note

Before tilting the outboard motor up, after
stopping the motor leave it in the running
position for about a minute to allow water
to drain from inside the engine.

ENOM01810-0

Power Trim & Tilt type

Tilt up

1. Press the power trim and tilt switch

"UP" until the motor has been tilted
up completely.

2. Pull the tilt stopper down as shown

below drawing.

1. 

Tilt stopper

3. Press the power trim and tilt switch

"DN" (Down) until the trim rods has
been retracted completely.

8. Tilt up and down

  

WARNING

  

WARNING

  

WARNING

  

CAUTION

ENOF02437-0

DN

UP

UP

DN

ENOF00067-2

UP

DN

ENOF00941-0

1

ENOF013190

Содержание MFS 115A

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды