manualshive.com logo in svg

TOHATSU MFS 115A, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 115A Скачать руководство пользователя страница 58

REMOVING AND CARRYING THE OUTBOARD MOTOR

58

8

Keep the outboard motor in a vertical
position when carrying.
The optional outboard motor stand is
recommended for keeping the outboard
motor vertical both during transport and
storage.

ENOM00072-A

ENOW00072-0

Trailering in the tilted position may cause
damage to the outboard motor, boat, etc.

ENOW00971-0

On applicable models remove the fuel con-
nector and fuel line except when operating
engine.
Fuel leakage is a fire or explosion hazard,
which can cause serious injury or death.

ENOW00068-0

Close air vent screw of fuel tank and fuel
cock before carrying or storing outboard
motor and fuel tank, or fuel may leak, poten-
tially catching fire.

ENOW00071-0

The tilt support device supplied on your out-
board motor is not intended for towing. It is
intended to support the outboard motor
while the boat is docked, beached, etc.

When transporting a boat on a trailer
with the outboard motor still attached,
disconnect the fuel line from the out-
board motor beforehand and keep the
outboard motor in the normal running
position or on a transom bar.

Tiller handle type

To prevent the outboard motor from
moving when it is attached on a boat
during transport on a trailer, properly
tig hte n  th e  ste e ring  fric tio n  le v e r
(page 60).

3. Trailering

  

CAUTION 

  

WARNING

ENOF02421-0

  

WARNING

  

CAUTION 

ENOF00075-1

Содержание MFS 115A

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды