Titan High Rider Basic Скачать руководство пользователя страница 9

Страница: 9 / 28

Cleanup

Special cleanup instructions for use with
flammable solvents:

• Always flush spray gun preferably outside and at least one

hose length from spray pump.

• If collecting flushed solvents in a one gallon metal

container, place it into an empty five gallon container, then
flush solvents.

• Area must be free of flammable vapors.
• Follow all cleanup instructions.

IMPORTANT: The sprayer, hose, and gun should be
cleaned thoroughly after daily use. Failure to do so
permits material to build up, seriously affecting the
performance of the unit.

Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for
latex paint or mineral spirits for oil-based paints.

4. Place the return hose into a metal waste container.
5. Move the PRIME/SPRAY valve down to its

PRIME position.

6. Set the pressure to Turbo PulseClean by

turning the pressure control knob to its
PULSE CLEAN position in the red zone.

7. Turn on the sprayer by moving the

ON/OFF switch to the ON position.

8. Allow the solvent to circulate through the unit and flush the

paint out of the return hose into the metal waste container.

9. Turn off the sprayer by moving the ON/OFF

switch to the OFF position.

10. Move the PRIME/SPRAY valve up to its

SPRAY position.

11. Turn on the sprayer.

Ground the gun by holding it against

the edge of the metal container while
flushing. Failure to do so may lead
to a static electric discharge, which
may cause a fire.

12. Trigger the gun into the metal waste

container until the paint is flushed out of the hose and
solvent is coming out of the gun.

13. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

14. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

15. Unplug the unit and store in a clean, dry area.

IMPORTANT: Do not store the unit under pressure.

NOTE: For long-term or cold weather storage, pump

mineral sprits through the entire system.
For short-term storage when using latex paint,
pump water mixed with Titan Liquid Shield
through the entire system (see the Accessories
section of this manual for part number).

Min PSI

(Bar)

Max PSI

(Bar)

lse

NOTE: Hold the return hose in the waste

container when moving the
PRIME/SPRAY valve to PRIME in
case the sprayer is pressurized.

Maintenance

Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. Always unplug the
sprayer before servicing!

General Repair and Service Notes

The following tools are needed when repairing this sprayer:

Phillips Screwdriver

3/8" Hex Wrench

Needle Nose Pliers

5/16" Hex Wrench

Adjustable Wrench

1/4" Hex Wrench

Rubber Mallet

3/16" Hex Wrench

Flat-blade Screwdriver

5/32” Hex Wrench

5/64” Hex Wrench

1. Before repairing any part of the sprayer, read the

instructions carefully, including all warnings.

IMPORTANT: Never pull on a wire to disconnect it. Pulling
on a wire could loosen the connector from the wire.

2. Test your repair before regular operation of the sprayer to

be sure that the problem is corrected. If the sprayer does
not operate properly, review the repair procedure to
determine if everything was done correctly. Refer to the
Troubleshooting Charts to help identify other possible
problems.

3. Make certain that the service area is well ventilated in

case solvents are used during cleaning. Always wear
protective eyewear while servicing. Additional protective
equipment may be required depending on the type of
cleaning solvent. Always contact the supplier of solvents
for recommendations.

4. If you have any further questions concerning your TITAN

Airless Sprayer, call TITAN:

Customer Service (U.S.) .......................

1-800-526-5362

Fax ................................................

1-800-528-4826

Customer Service (Canada) ..................

1-800-565-8665

Fax ................................................

1-905-856-8496

Customer Service (International)...........

1-201-337-1240