Titan High Rider Basic Скачать руководство пользователя страница 5

Страница: 5 / 28

Preparing to Paint

Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.

IMPORTANT: Always keep the trigger lock on the spray
gun in the locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for
latex paint or mineral spirits for oil-based paints.

2. Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning

the pressure control knob to the “Min”
setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF switch to the

ON position.

6. Allow the sprayer to run for 15–30 seconds to flush the old

solvent out through the return hose and into the metal
waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

8. Move the PRIME/SPRAY valve up to the

SPRAY position.

9. Turn on the sprayer.

10. Unlock the gun by turning the gun trigger

lock to the unlocked position.

Ground the gun by holding it
against the edge of the metal
container while flushing. Failure
to do so may lead to a static
electric discharge, which may
cause a fire.

11. Trigger the gun into the metal waste container until the old

solvent is gone and fresh solvent is coming out of the gun.

12. Lock the gun by turning the gun trigger

lock to the locked position.

13. Set down the gun and increase the

pressure by turning the pressure control
knob slowly clockwise into the green zone.

14. Check the entire system for leaks. If

leaks occur, follow the “Pressure Relief
Procedure” in this manual before tightening any fittings or
hoses.

15. Follow the “Pressure Relief Procedure” in this manual

before changing from solvent to paint.

Be sure to follow the pressure relief procedure
when shutting down the sprayer for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.

Trigger lock in

locked position.

NOTE: Make sure that the spray gun does not have a

tip or tip guard installed.

NOTE: Hold the return hose in the waste

container when moving the
PRIME/SPRAY valve to PRIME in
case the sprayer is pressurized.

Min PSI

(Bar)

Max PSI

(Bar)

lse

NOTE: Incompatible fluids and paint may cause the

valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer’s fluid section.

Painting

1. Place the siphon tube into a container of paint.
2. Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning

the pressure control knob to the “Min”
setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

6. Allow the sprayer to run until paint is coming

through the return hose into the metal waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

8. Remove the return hose from the waste container and place

it in its operating position above the container of paint.

9. Move the PRIME/SPRAY valve up to the

SPRAY position.

10. Turn on the sprayer.

11. Unlock the gun by turning the gun trigger

lock to the unlocked position.

Ground the gun by holding it

against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.

12. Trigger the gun into the metal waste container until all air

and solvent is flushed from the spray hose and paint is
flowing freely. from the gun.

13. Lock the gun by turning the gun trigger

lock to the locked position.

14. Turn off the sprayer.
15. Attach tip guard and tip to the gun as

instructed by the tip guard or tip manuals.

POSSIBLE INJECTION HAZARD.
Do not spray without the tip guard
in place. Never trigger the gun
unless the tip is in either the spray or the unclog
position. Always engage the gun trigger lock
before removing, replacing or cleaning tip.

16. Turn on the sprayer.
17. Increase the pressure by turning the pressure control knob

slowly clockwise toward the green zone and test the spray
pattern on a piece of cardboard. Adjust the pressure control
knob until the spray from the gun is completely atomized.
Try to keep the pressure control knob at the lowest setting
that maintains good atomization.

Control Panel Indicators

The following is a description of the control panel indicators.

Min PSI

(Bar)

Max PSI

(Bar)

Blinking Yellow

0-200 PSI

Solid Yellow

201-1900 PSI

Solid Green

1901-3300 PSI