Titan Attachments 191587 Скачать руководство пользователя

Страница: 9 / 50

2. PACKING LIST

The detailed packing list of the mower and accessory as the following table 1-1.

ITEM

DESCRIPTION

QTY

PACKAGE FORM

(1)

MAIN BODY

NONE

(2)

WHEEL TIRE ASSEMBLY AND FITTINGS

BUBBLE FILM

(3)

FRONT AND REAR BRACES

BUBBLE FILM

(4)

PIVOTING UPPER HITCH-BLACK AND FITTINGS

BUBBLE FILM

(5)

R&L SKUD WELDMENT AND FITTING

BUBBLE FILM

(6)

DRIVELINE SHAFT WITH CLUTCH

BUBBLE FILM

(7)

WHEEL TIRE ASSEMBLY AND FITTING

BUBBLE FILM

(8)

BOLT M10*20

BUBBLE FILM

(9)

BOLT M10*55

CRATE ATTACHMENT

(10) REMOVABLE ANGLE STEEL

CRATE ATTACHMENT

(11) LOCK NUT M10

CRATE ATTACHMENT

(12) BOLT M10*20

CRATE ATTACHMENT

(13) REMOVABE ANGLE STEEL SUPPORT

CRATE ATTACHMENT

(14) IRON CRATE

CRATE ATTACHMENT

Table 1-1

: Packing List of The PRO Rotary Cutter and Accessory

The detailed description of Wheel Frame Weldment And Fittings

ITEM

DESCRIPTION

QTY

(1)

NYLON WASHER 16

(2)

LOCK NUT M16

(3)

PLAIN WASHER 16

(4)

BOLT M16*90

(5)

SAFETY LOCK PIN 8*45

(6)

NYLON WASHER 16

Содержание 191587



















































Результаты поиска

Содержание 191587

Отзывы:

Похожие инструкции для 191587

Бренды по названию

Популярные бренды

Titan Attachments 191587, Руководство оператора

Результаты поиска

Содержание 191587

Отзывы:

Похожие инструкции для 191587

Бренды по названию

Популярные бренды