Tiger TRIPLE FLAIL JD5 M T4F Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 240

background image

OPERATION

Boom

Operation Section 3-12

©2013 Alamo Group Inc.

OPERA

T

ION

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement.
Place the Mower Head on the ground or securely supported on blocks or stands, disengage

the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times

to relieve pressure prior to starting any maintenance or repair work.

(SBM-6)

Never Leave the mower unattended while the head is in the raised
position. The mower could fall causing serious injury to anyone who

might inadvertently be under the mower

.

(SBM-4)

BOOM ARM ASSEMBLY

•

Inspect condition of each arm section weldment

•

Ensure all pins are in place.

•

Ensure all bolts, nuts and rollpins are properly
installed.

•

Check condition of bushings at boom pivot
points and hydraulic cylinder tangs.

•

Ensure each hydraulic cylinder is installed and
retained correctly. Ensure the proper size pins
are used to retain the cylinders in place and are
secured properly.

OPS-B- 0022_D

Never attempt to lubricate, adjust, or remove material from the Implement while it is in
motion or while tractor engine is running.

(SG-20)

HYDRAULIC LINE INSPECTION

•

Check for hydraulic leaks along hoses,
cylinders and fittings.

IMPORTANT

: DO NOT

use your hands to check for oil leaks. Use a
piece of heavy paper or cardboard to check for
hydraulic oil leaks.

•

Inspect the condition of the valve mounting.

•

Ensure fittings are properly connected.

OPS-B- 0023_D

«
...
62
63
64
65
66
...
»

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRIPLE FLAIL JD5 M T4F Series

Бренд: Yard-Man Страницы: 36

Бренд: Lastec Страницы: 56

Бренд: EarthWise Страницы: 9

Бренд: LawnMaster Страницы: 28

Бренд: Ransomes Страницы: 184

Бренд: Weed Eater Страницы: 48

Бренд: Euro garden Страницы: 84

Бренд: Toro Страницы: 60

Бренд: Worx Страницы: 64

Бренд: Sabo Страницы: 94

Бренд: Tar River Страницы: 32

Бренд: Far Tools Страницы: 21

Бренд: Cub Cadet Страницы: 16

Бренд: VITO GARDEN Страницы: 40

Бренд: dormak Страницы: 24

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды