Tiger TRIPLE FLAIL JD5 M T4F Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 240

background image

OPERATION

Boom

Operation Section 3-3

©2013 Alamo Group Inc.

OPERA

TION

1.OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator.  A qualified operator has read and
understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor
operation and all associated safety practices.  In addition to the safety messages contained in this manual,
safety signs are affixed to the implement and tractor.  If any part of the operation and safe use of this
equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the
equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and
operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE)
for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to
provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

•

Always Wear Safety Glasses

•

Hard Hat

•

Steel Toe Safety Footwear

•

Gloves

•

Hearing Protection

•

Close Fitting Clothing

•

Respirator or Filter Mask (depends on
operating conditions)

(OPS-U- 0002)

NEVER use drugs or alcohol immediately before or while operating the
Tractor and Implement. Drugs and alcohol will affect an operator’s
alertness and coordination and therefore affect the operator’s ability to
operate the equipment safely. Before operating the Tractor or Implement,
an operator on prescription or over-the-counter medication must consult
a medical professional regarding any side effects of the medication that
would hinder their ability to operate the Equipment safely. NEVER
knowingly allow anyone to operate this equipment when their alertness or
coordination is impaired. Serious injury or death to the operator or others
could result if the operator is under the influence of drugs or alcohol.

(SG-27)

«
...
53
54
55
56
57
...
»

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRIPLE FLAIL JD5 M T4F Series

Бренд: Ryobi Страницы: 16

Бренд: Jacobsen Страницы: 36

GRASS KEEPER 190 W

Бренд: Garland Страницы: 136

TURF TIGER STT61V-31KB-DF

Бренд: Scag Power Equipment Страницы: 78

Бренд: Lawn-Boy Страницы: 16

Бренд: GrassFlap Страницы: 14

Бренд: Stihl Страницы: 24

Бренд: MTD Страницы: 24

GLM 40/140 P EASY

Бренд: F.F. Group Страницы: 96

Бренд: Ayce Страницы: 118

Бренд: Garland Страницы: 47

Бренд: Scag Power Equipment Страницы: 96

Бренд: Cub Cadet Страницы: 39

Бренд: Nakayama Страницы: 80

Бренд: Craftsman Страницы: 60

Бренд: Flymo Страницы: 12

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды