Tiger TRIPLE FLAIL JD5 M T4F Series Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 240

background image

OPERATION

Boom

Operation Section 3-30

©2013 Alamo Group Inc.

OPERA

T

ION

8.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating
condition. Tractor brakes can be set to operate
independently allowing single rear wheel braking
action or locked together to provide simultaneous
rear wheel braking. FOR MOST DRIVING AND
OPERATING CONDITIONS, THE BRAKE PEDALS
SHOULD BE LOCKED TOGETHER TO PROVIDE
THE MOST EFFECTIVE BRAKING ACTION.

Always disengage the tractor differential lock when
turning. When engaged the differential lock will
prevent or limit the tractor from turning. During
normal cutting conditions, locking the differential
provides no benefit and should not be used.

OPS-U- 0013

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes.
When operating down a hill or on wet or rain slick roads, the braking distance increases;
use extreme care and reduce your speed in these conditions. When operating in traffic,

always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and
watch out for the other guy.

(Ops-0004-MISC)

BEFORE leaving the tractor seat, always set the parking brake and/or set
the tractor transmission in parking gear, disengage the PTO, stop the
engine, remove the key, and wait for all moving parts to stop. Place the
tractor shift lever into a low range or parking gear to prevent the tractor
from rolling. Never dismount a Tractor that is moving or while the engine
is running. Operate the Tractor controls from the tractor seat only.

(SG-9)

«
...
80
81
82
83
84
...
»

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRIPLE FLAIL JD5 M T4F Series

Бренд: Kärcher Страницы: 32

Бренд: Peco Страницы: 12

Бренд: Gardenline Страницы: 24

Бренд: Gardena Страницы: 290

Бренд: Walker Rider Lawnmowers Страницы: 100

Бренд: Kubota Страницы: 59

Бренд: Dolmar Страницы: 284

Бренд: EMAK Страницы: 64

S1642, S1742, S2046

Бренд: Scotts Страницы: 72

Бренд: Honda Страницы: 28

Бренд: Tianchen Страницы: 20

Бренд: Toro Страницы: 56

Reelmaster 5610-D

Бренд: Toro Страницы: 84

Бренд: Viking Страницы: 588

Бренд: Kubota Страницы: 106

Бренд: Kubota Страницы: 95

Бренд: Columbia Страницы: 24

sunjoe 24V-X2-21LMSP-CT

Бренд: SNOWJOE Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды