manualshive.com logo in svg

Tiger TRIPLE FLAIL JD5 M T4F Series, Монтаж и эксплуатация, Страница: 108 / 240

Поделиться
Скачать
Tiger TRIPLE FLAIL JD5 M T4F Series Скачать руководство пользователя страница 108

MAINTENANCE

Boom

Maintenance Section 4-10

©2020 Alamo Group Inc.

MAINTENANCE

POLYCARBONATE CARE AND MAINTENANCE

The proprietry UV and Abrasion Resistant Surface coating on SHIELDS SUPERCOATED polycarbonate
significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are
recommended to prolong service life. Tiger Corp. polycarbonate is SUPERCOATED on both sides.

CLEANING THE SUPERCOAT HARD-COAT

1.

Wash with a mild solution of soap or detergent and lukewarm water.

2.

Using a soft cloth or sponge, gently wash the sheet to loosen dirt and grime and rinse well with clean 
water.

3.

To prevent water spotting, thoroughly dry with chamois or cellulose sponge.

4.

Avoid the use of abrasive cleaners, squeegees and/or other cleaning implements that may mar or 
gouge the coating.

CLEANING AGENTS WHICH HAVE BEEN FOUND TO BE COMPATIBLE UNDER LABORATORY
CONDITIONS:

Aqueous Solutions of Soaps and Detergents

Windex(1)

Top Job(2)

Joy(2)

Mr Clean(2)

Fantastik(3)

Formula 409(4)

Sumalight D12

Brucodecid

Organic Solvents

Butyl Cellosolve

Kerosene

Hexel, F.O. 554

Naphtha(VM&P grade)

Neleco-Placer

Turco 5042

Alcohols

Methanol

Isopropyl

All residual organic solvents should be removed with a secondary rinse.

GRAFFITI REMOVAL

Butyl cellosolve (for removal of paints, marking pen inks, lipstick, etc.) The use of masking tape, adhesive tape
or lint removal tools work well for lifting off old weathered paints.

To remove labels, stickers, etc., the use of kerosene or VM&P naphtha is generally effective. When the solvent
will not penetrate sticker material, apply heat (hair dryer) to soften the adhesive and promote removal.

IMPORTANT: If a material is found to be incompatible in a short-term test, it will usually be found to be
incompatible in the field. The converse, however, is not always true. Favorable performance is no guarantee
that actual end-use conditions have been duplicated. Therefore, these results should be used as a guide only
and it isrecommended that the user test the products under actual end-use conditions. 

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы:

Нет отзывов