manualshive.com logo in svg

Tiger TRIPLE FLAIL JD5 M T4F Series, Монтаж и эксплуатация, Страница: 47 / 240

Поделиться
Скачать
Tiger TRIPLE FLAIL JD5 M T4F Series Скачать руководство пользователя страница 47

ASSEMBLY

Assembly Section 2-17

WHEEL WELL HYDRAULIC TANK INSTALLATION

Install all fittings and tubes into tank and tank filter as shown in the Parts Section illustration.  

Insert tank sight glass onto the tractor side of the tank.

Place the tank in the mounting bracket on the axle brace as shown in the Parts Section.  

Secure the tank with the hardware provided.

Install the filter gauge into the filter housing so that it points to the rear of the tractor and is 

clearly visible to the operator.  The tank breather cap is ready for use as the tank is filled. Some 
of these items may already be installed.

   (ASM-C-0103)

FILLING HYDRAULIC RESERVOIR

Refer to the Maintenance Section for filling specifications and hydraulic oil requirements.

NOTE: Starting or running your Tiger mower before filling reservoir will cause
serious damage to the hydraulic pump.

(ASM-C-0004hydro resrv)

WHEEL SPACERS

When mounting a boom mower, a spacer kit is needed for both rear wheels  After removing

the wheels attach the spacer to the wheel portion of the axle with the hardware provided.   When
you are ready to re-attach the wheel, the wheel goes on first then the reinforcement ring and
finally the hardware provided.  

(ASM-JD-0099)

INSTALLING O-RING FITTINGS

Installing straight, 45º and 90º O-rings requires that the O-ring and washer be up against the

swivel body.  Insert the swivel and turn in until the swivel is pointed in the desired direction and O-
ring contact is made.  Hold swivel in set direction with a wrench and turn the O-ring nut away
from the swivel body and carefully tighten.  

(ASM-C-0056)

GENERAL HOSE INSTALLATION

Refer to the Parts Section for detailed information about hoses and fittings for this

application. 

(ASM-C-0011)

HOSE COVERING

Secure hoses together with zip ties wherever loose.   Wrap the hoses between the swivel and

main boom with the hose cover provided.  Wrap the hoses between the main boom and
secondary boom with the hose cover provided.  Where hoses may contact the frame or other
edges, wrap with split hose and secure with hose clamps or zip ties.

On non-cab units, the pressure and return hoses from the control valve will also need to be

routed inside the protective  hose wrap.  Cover the valve and valve fittings with the hose cover
and secure with the string provided.  

(ASM-C-0058)

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы:

Нет отзывов