background image

OPERATION

Boom

Operation Section 3-17

©2013 Alamo Group Inc.

OPERA

TION

Tractor PRE-OPERATION Inspection

Mower ID#________________

Make ____________________

Date:       ________________

Shift

____________________

Before conducting the inspection, make sure the tractor engine is off, all rotation
has stopped and the tractor is in park with the parking brake engaged. Make sure
the mower is resting on the ground or securely blocked up and all hydraulic
pressure has been relieved.

Operator’s Signature:

Item

Condition at Start 

of Shift

Specific Comments 

if not O.K.

The flashing lights function properly
The SMV Sign is clean and visible
The tires are in good condition with proper pressure
The wheel lug bolts are tight
The tractor brakes are in good condition
The steering linkage is in good condition
There are no visible oil leaks
The hydraulic controls function properly
The ROPS or ROBS Cab is in good condition
The seatbelt is in place and in good condition
The 3-point hitch is in good condition
The drawbar pins are securely in place
The PTO master shield is in place
The engine oil level is full
The brake fluid level is full
The power steering fluid level is full
The fuel level is adequate
The engine coolant fluid level is full
The radiator is free of debris
The air filter is in good condition

DO NOT OPERATE an UNSAFE TRACTOR or MOWER

This Inspection Form may be freely duplicated for extra copies.

Содержание TRIPLE FLAIL JD5 M T4F Series

















































































































































































































































Отзывы: