THORLABS BNT001/IR Скачать руководство пользователя страница 16

Страница: 16 / 49

HA0114T Rev 10 May 2019

Chapter 3

'Settings' list. Note. Use of this control will automatically switch the circle diameter

adjustment mode to 'Manual'.

Settings list

- shows user specified settings for the parameters listed below. Note.

Some parameters can also be configured for automatic adjustment. When operating

in the relevant 'Auto' mode, the user specified values displayed may be different to

the actual values applied (and in some cases, displayed on the CRT).

User Diameter

- displays the circle diameter (in NT units). The circle diameter can

be set either by adjusting the manual control knob or by calling a software

function.

Frequency -

displays the scanning frequency (in Hz). The scanning frequency can

be set either by entering a value in the 'Settings' panel, or by calling a software

function.

Phase Angle

- displays the phase compensation values (in degrees) for the

horizontal and vertical components of the circle path. Values can be entered in the

'Tracking' settings panel. Note. If the phase compensation adjustment mode is set

to 'Auto', the actual phase offset may be different to the diameter displayed. (see

Section C.1.4. for further information).

Loop Gain

- displays the gain setting for the NanoTrak control loop. The gain can

be set either by entering a value in the 'Tracking' settings panel.

Signal Source

- displays the type of input source connected. The input source is

set by entering a value in the 'Input/Output' settings panel.

Diameter Mode

- displays the mode of circle diameter adjustment as follows:

User

Diameter adjusted by the user

LUT

Diameter adjusted via Look Up Table

(set via the Tracking tab).

Settings button

- Displays the 'Settings' panel, which allows the NanoTrak’s

operating parameters to be entered - see Section 3.9.

Identify

- when this button is pressed, the channel LEDs on the I/O panel of the

associated hardware module will flash for a short period.

Note

If the circle diameter adjustment mode is set to 'Auto', the actual circle diameter

(displayed on the CRT) may be different to the diameter displayed in the Settings

window. (see Section C.1.3. for further information).

Содержание BNT001/IR


















































Результаты поиска

Содержание BNT001/IR

Отзывы:

Похожие инструкции для BNT001/IR

Бренды по названию

Популярные бренды

THORLABS BNT001/IR, Руководство пользователя

Результаты поиска

Содержание BNT001/IR

Отзывы:

Похожие инструкции для BNT001/IR

Бренды по названию

Популярные бренды