manualshive.com logo in svg

THORLABS BNT001/IR, Руководство пользователя

Поделиться
Скачать
THORLABS BNT001/IR Скачать руководство пользователя страница 11

8

NanoTrak Autoalignment Controller

3.5 Installing the Software

DO NOT CONNECT THE CONTROLLER TO YOUR PC YET

1) Go  to  Services/Downloads  at  www.thorlabs.com  and  download  the  Kinesis

Software.

2) Run the .exe file and follow the on-screen instructions.

3.6 System Setup

3.6.1 Initial Setup

1) Install the software as detailed in Section 3.5.
Connect the controller to the actuators (see Section 4.2.3.) and the PC, then switch

ON. Wait approximately 5 seconds for the system to settle.

Caution

IIf your PC becomes unresponsive (e.g due to an operating system problem,

entering a sleep state condition, or screen saver operation) for a prolonged

period,  this  will  interrupt  communication  between  the  software  and  the

hardware,  and a communications error  may  be  generated. To minimize the

possibility of this happening it is strongly recommended that any such modes

that result in prolonged unresponsiveness be disabled before the software is

run. Please consult your system administrator or contact Thorlabs technical

support for more details.

Caution

Some  PCs  may  have  been  configured  to  restrict  the  users  ability  to  load

software, and on these systems the  software may not install/run. If you are in

any doubt about your rights to install/run software, please consult your system

administrator before attempting to install. If you experience any problems when

installing  software,  contact  Thorlabs  on  +44  (0)1353  654440  and  ask  for

Technical Support.

Caution

IIn applications requiring the highest level of accuracy and repeatability, it is

recommended that the controller unit is powered up approximately 30 minutes

before use, in order to allow the internal temperature to stabilize.

Содержание BNT001/IR


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды