manualshive.com logo in svg

THORLABS BNT001/IR, Руководство пользователя

Поделиться
Скачать
THORLABS BNT001/IR Скачать руководство пользователя страница 26

23

HA0114T Rev 10 May 2019

Chapter 3

3.9.4 HV Settings Tab

Fig. 3.9   NanoTrak Settings panel - HV Amps tab

This panel is used to set the output characteristics of the HV amplifier channels fitted

to the NanoTrak unit. Both low pass filtering and current control settings can be made

to tailor the piezo output drive to a particular application.

HV Amplifier Settings

Low Pass Filter

 – This parameter sets the cut off frequency of the hardware low pass

filter,  applied  to  the  HV  amplifier  output  channels.  It  applies  to  both  channels

simultaneously.

10HZ - Cut off all signals above 10Hz
100HZ - Cut off all signals above 100Hz
5KHZ - Cut off all signals above 5KHz
NONE - Low pass filter inactive

Channel 1 and Channel 2

Current Limits

 - This parameter sets the maximum current output of the HV amplifier:

100MA – Current output (piezo drive signal) limited at 100mA
250MA – Current output (piezo drive signal) limited at 250mA
500MA– Current output (piezo drive signal) limited at 500mA

Note

This low pass filter setting is different to the low pass filter specified using the Input/

Output tab.

Содержание BNT001/IR


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды