THORLABS BNT001/IR Скачать руководство пользователя страница 5

Страница: 5 / 49

1.3 PC Software Overview

1.3.1 Introduction

The BNT001 NanoTrak controllers feature USB connectivity (allowing multiple units

to be used together on a single PC), fully featured Graphical User Interface (GUI)

panels, and extensive software function libraries for custom application development.
The Kinesis software suite provides a flexible and powerful PC based control system

both for users of the equipment, and software programmers aiming to automate its

operation.
The User Interface allows full control of all settings and operating modes enabling

complete ‘out-of-box’ operation without the need to develop any further custom

software. It provides all of the necessary system software services such as generation

of GUI panels, communications handling for multiple USB units, and logging of all

system activity to assist in hardware trouble shooting. The Kinesis server is also used

by software developers to allow the creation of advanced automated positioning

applications very rapidly and with great ease. The server is described in more detail

in the following section.

1.3.2 Kinesis Server

With the Kinesis system, .Net Controls are deployed to allow direct control over (and

also reflect the status of) the range of electronic controller units, including the Piezo

controller. Software applications that use .Net Controls are often referred to as 'client

applications'. A .Net Control is a language independent software component.

Consequently the controls can be incorporated into a wide range of software

development environments for use by client application developers. Development

environments supported include Visual Basic, Labview, Visual C++, C++ Builder,

HPVEE, Matlab, VB.NET, C#.NET and, via VBA, Microsoft Office applications such as

Excel and Word.
Consider the control supplied for the BNT001 controller.

Содержание BNT001/IR


















































Результаты поиска

Содержание BNT001/IR

Отзывы:

Похожие инструкции для BNT001/IR

Бренды по названию

Популярные бренды

THORLABS BNT001/IR, Руководство пользователя

Результаты поиска

Содержание BNT001/IR

Отзывы:

Похожие инструкции для BNT001/IR

Бренды по названию

Популярные бренды