background image

Page 4 of 18 

 

2. Safety 

 

2.1 Proper use 

 
The intended use of the machine is only drying and polishing chrome, steel, or silver cutlery. The following cutlery 
pieces can be used: 
 
► spoon  

 

 

 

► fork 

► knife   

 

 

 

► small fork 

► tea spoon 
 
 

2.2 Improper use 
 

The machine is not designed to polish any other sorts of cutlery or foreign utensils. Any other use is not according to 
regulations and therefore prohibited. We take no responsibilities for damage caused by improper use. 
 

2.3 General safety instructions 
 

 
 
 

Warning! 

Death or serious injury may accur by means of electrical shock 
 

>

 

Never install or operate the machine with a damaged power cord. 

>

 

By suspicion of damage, for example an electrical fault smell, disconnect the machine from the power circuit 
immediately and contact the Dörr-service personnel. 

>

 

A damaged power cable can only be repaired by a Dörr-service member or a from Dörr authorized service 
technician. 

>

 

Make sure the power cable is never placed near a hot surface. 

>

 

Make sure the power cable is never pinched or brushed along a sharp edge or surface. 

>

 

Never open and repair the machine yourself. Make no changes to the machine that are not listed in this manual. 
This device contains electrical current-carrying parts. After opening, the risk of death or serious injury could 
occur. Repairs can only be made by Dörr authorised service technicians with original Dörr spare parts and 
accessories. 

>

 

Never expose the machine to gushes or jets of water. 

Caution! 

Risk of injury 
 

>

 

Any installed safety components are not to be changed or demounted. 

>

 

Never put your hands in the machine. 

>

 

To prevent cuts always insert cutlery by holding the handle of the cutlery. 

>

 

Never touch hot parts. 

>

 

Never let the power cord hang loose. It could be tripped over or damaged. 

>

 

Before performing any cleaning or maintenence work be sure that the power 

switch is turned off to  “O” and the 

power cord is disconnected. 

>

 

Turn the machine off when not using it for a longer period of time. 

>

 

This device must be installed to an appropriate connected power circuit.(See page 15) 

>

 

Exclusively use the original Dörr Polishing Granulate SG 3000L as well as original Dörr cleaning products. 

>

 

Install the device far from the reach of children. 

>

 

Persons, including children, who by reason of physical,sensual or mental complications or unexperience or 
ignorance may not operate the machine without guidance from a responsible person. 

>

 

Persons who are not capable of reading or cannot read  this manual`s language must be educated and trained 
about the contents of this manual and operation of the machine. 

Содержание TD 3000L M14



















Отзывы: