ThingMagic Astra-EX Скачать руководство пользователя страница 45

Страница: 45 / 94

Controlling the Reader

M6 and Astra-EX User Guide

Query Page

Use the M6 and Astra-EX Query Page to set up and run Anti-Collision Searches quickly,

and to obtain immediate feedback. This is useful for debugging as well as for verifying
performance after installation is completed.

If the Query page does not load and you do not see the Java logo, install the Java

Runtime Environment for your platform and restart your PC.

Note

Use of the Query applet, or any Reader client application, requires port 5084 to be
open on the network. If the Query applet

Connect

fails to connect it is likely either

another client already has an open connection or port 5084 is being blocked by a
firewall.

The basic steps to connect, read, modify the read behavior and display options are

defined in the following sections:

 

Read Tags

 

Query Results

 

Query Settings

In addition to modifying the query behavior using the

Query Settings

, the performance of

the reader can be optimized for a particular usecase by making changes to the

Gen2

Protocol Settings

Read Tags

To read tags under default performance and display options:

Click

Connect

to reader. A connection will not be successful if other clients are

connected to the reader.

Figure 14:

Query Page - Connect

Position one or more tags, in front of one of the antennas connected to the
Reader.

Click

Read

Содержание Astra-EX































































































Результаты поиска

Содержание Astra-EX

Отзывы:

Похожие инструкции для Astra-EX

Бренды по названию

Популярные бренды

ThingMagic Astra-EX, Руководство пользователя

Результаты поиска

Содержание Astra-EX

Отзывы:

Похожие инструкции для Astra-EX

Бренды по названию

Популярные бренды