background image

 

INTRODUCTION 

 

This appliance is designed for cooking foods and any other use is incorrect and 

may be dangerous.  Failure to install the appliance correctly or improper use will 

invalidate any warranty or liability claims.  

This appliance must only be installed by a qualified installer or engineer in 

accordance with the relevant local and national regulations in force. Failure to 

install the appliance correctly could invalidate any warranty or liability claims and 

lead to prosecution. Please refer to the methods of installation and use supplied 

with this appliance. 

Our policy is one of continuous development and improvement. Specifications 

and illustrations may change without notice, subsequent to publication. 

 

Provision of ventilation 

The use of a gas cooking appliance results in the production of heat, moisture 

and products of combustion

 

in the room in which it is installed. Ensure that the 

area where the appliance is used is well ventilated especially, when the 

appliance is in use. Keep natural ventilation holes open or install a mechanical 

ventilation device (mechanical extractor hood). 

Prolonged intensive use of the appliance may call for additional ventilation, for 

example opening of a window, or more effective ventilation, for example 

increasing the level of mechanical ventilation where present. 

The room containing the cooker shall be ventilated in accordance with all local 

and national regulations in force.  

 

Initial Cleaning 

Before using the hob for the first time, check the power supply is switched off and 

use a dampened soft cloth to remove any soiling or residual factory lubricants. 

Once clean apply a thin coating of ceramic glass cleaner conditioner to the glass 

surface and polish with a clean dry cloth. 

 

The conditioner provides a protective surface coating which will make cleaning 

the hob easier. Occasionally reapplying the conditioner will reduce the 

accumulation of deposits from cooking. 

 

If the glass surface becomes discoloured due to cooking deposits, clean the 

glass using a mild cream cleaner or use a ceramic hob scraper. Wipe the surface 

clean and re-apply the cleaner conditioner. See Care and Maintenance section. 

 

This appliance is approved for use with Universal LPG. 

The burners on this appliance have fixed aeration and no adjustment is required. 

The burners should flame as follows; 

 

ULPG:  

Normally on initial lighting, a small amount of yellow tipping will 

occur which increases slightly as the burner heats up. 

 

Содержание SHB981 Series























Отзывы: