manualshive.com logo in svg

Thermo Orion 410Aplus, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Orion 410Aplus Скачать руководство пользователя страница 58

G. Orion 520Aplus, 525Aplus, 720Aplus Dissolved 

Oxygen Measurements 

Dissolved Oxygen measurements are displayed in ppm when the Orion
9708  Dissolved Oxygen Electrode (Orion 970899) is used with the Orion
520Aplus, 525Aplus and 720Aplus and 920Aplus Meters. Perform the
following steps to prepare the meter and calibrate the electrode.

1. Connect the D.O. electrode Orion 9708 to meter. Leave electrode 

mode switch “OFF”. 

2. For the Orion 525Aplus and 720Aplus select the correct channel by 

pressing 

2nd 

then

channel

.

3. Disconnect ATC probe.

NOTE:  

ATC probe must not be connected to the meter 

and the meter should be calibrated to pH 7 at 25.0˚C.

4. Press 

mode

until pH mode indicator is displayed.

5. Press 

hold

. Turn the 

hold 

feature off.

6. Press

measure

. Press 

set temp

. Enter 25.0 at the prompt and 

press 

yes

.

7. Press 

calibrate

. Enter 

1 

at the ENTER NO. OF BUFFER prompt 

and press 

yes

.

8. Enter 7.00 to the CAL AS  prompt and press 

yes.

9. At the slope prompt enter 100.0 and press 

yes.

The meter 

automatically returns to measure mode.

10. Turn the mode switch on the electrode to BT CK. Good battery 

operation is indicated by a reading of 13.40 or greater on the meter.

11. Turn the mode switch on the electrode to ZERO. Use the zero 

calibration control on the electrode to set the meter to read 0.00.

Orion Benchtop pH/ISE Meter Instruction Manual

Other Measurement Modes

54

Содержание Orion 410Aplus




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды