Thermo Orion 410Aplus Скачать руководство пользователя | Manualshive

Страница: 56 / 131

background image

Orion Benchtop pH/ISE Meter Instruction Manual

Other Measurement Modes

52

E. Orion 410Aplus Dissolved Oxygen Measurements

Dissolved Oxygen measurements are displayed in ppm when the Orion
9708 Dissolved Oxygen Electrode (Orion 970899) is used with the Orion
410Aplus Meter. Perform the following steps to prepare the meter and
calibrate the electrode.

1. Connect the Orion 9708 to meter and leave electrode mode

switch “OFF”.

2. Disconnect ATC probe.

NOTE:

ATC probe must not be connected to the meter

and the meter should be calibrated to pH 7 at 25.0˚C.

3. Press

mode

until MEASURE is displayed, if not already displayed.

4. Turn the mode switch on the electrode to BT CK. Good battery

operation is indicated by a reading of 13.40 or greater on the meter.

5. Turn the mode switch on the electrode to ZERO. Use the zero

calibration control on the electrode to set the meter to read 0.00.

6. Insert the reservoir (funnel) into a BOD bottle, containing enough

water to just cover the bottom. Insert the electrode, making sure that
the electrode tip is not immersed in the water and does not have water
droplets clinging to the outside of the membrane. Let stand
approximately 30 minutes to ensure water saturation of air in the BOD
bottle. This bottle should be used for storage between measurements.

7. Turn the electrode mode switch to the AIR position. If measurements

are made at sea level, use the AIR calibration control on the
electrode to set the pH meter reading to the prevailing barometric
pressure in mm Hg (divided by 100). If the barometric pressure is
unknown, the elevation is above sea level or the sample has a
salinity greater than two parts per thousand, consult

Table 1

found in the

Orion 9708 Instruction Manual

to obtain the correct

AIR setting.

8. Turn the electrode mode switch to H

2

O for sample analysis.

9. Record direct ppm reading from meter.

F. Orion 420Aplus, 710Aplus Dissolved

Oxygen Measurements

Dissolved Oxygen measurements are displayed in ppm when the Orion 9708
Dissolved Oxygen Electrode (Orion 970899) is used with the Orion 420Aplus and
710Aplus Meters. Perform the following steps to prepare the meter and calibrate
the electrode.

«
...
54
55
56
57
58
...
»

Содержание Orion 410Aplus




































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion 410Aplus

Бренд: B meters Страницы: 18

Бренд: B meters Страницы: 14

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Vortex Flow Industry

Бренд: Grundfos Страницы: 16

Бренд: Spacelabs Страницы: 156

Бренд: Caen Страницы: 63

Бренд: Caen Страницы: 35

Бренд: YATO Страницы: 52

Бренд: Heyl Страницы: 2

Бренд: PKP Страницы: 7

Бренд: Metrohm Страницы: 81

Бренд: Zensol Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды