Thermo Scientific Thermo Scientific Vanquish VC-D40 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 174

background image

5

•

Installation

Variable Wavelength Detectors (VC-D40, VF-D40)
Operating Manual

Page 49

5.3

Site Requirements

The operating environment is important to ensure optimal performance
of the device. This section provides important requirements for the
installation site. Note the following:

•

Operate the device only under appropriate laboratory conditions.

•

The device is intended to be part of the Vanquish system. Observe
the site requirements for the Vanquish system as stated in the

Vanquish System Operating Manual

.

•

For specifications, see

Specifications (

and the

Specifications

sections in the

Operating Manuals

for the other

modules in the Vanquish system.

•

For general residual hazards, see

General Residual Hazards

.

5.3.1

Power Considerations

The power supply of the device has wide-ranging capability, accepting
any line voltage in the range specified for the device.

CAUTION—Electric Shock or Damage to the Device

Connecting the device to a line voltage higher or lower than specified
could result in personal injury or damage to the device.

Connect the device to the specified line voltage only.

5.3.2

Power Cord

The power cords are designed to match the wall socket requirements of
the country in which they are used. The end of the power cords that
plugs into the power socket on the device is identical for all power cords.
The end of the power cords that plugs into the wall socket is different.

«
...
47
48
49
50
51
...
»

Содержание Thermo Scientific Vanquish VC-D40















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Thermo Scientific Vanquish VC-D40

Бренд: D-Link Страницы: 16

Бренд: D3D Страницы: 4

Бренд: Samsung Страницы: 1

iPOLiS SNP-3120

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 7

Бренд: Samsung Страницы: 23

iPOLiS SNP-3120

Бренд: Samsung Страницы: 2

iPolis SNO-5080R

Бренд: Samsung Страницы: 60

Бренд: OI Analytical Страницы: 133

Бренд: VHD Страницы: 2

Бренд: Panasonic Страницы: 42

Бренд: Axis Страницы: 26

Бренд: BBC Страницы: 16

Бренд: Wheelock Страницы: 10

Бренд: Gallagher Страницы: 67

Бренд: Zavio Страницы: 108

.WDR Camera Series

Бренд: Digital Equipment Страницы: 10

Бренд: Dante Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды