Thermo Scientific Thermo Scientific Vanquish VC-D40 Скачать руководство пользователя страница 15

Страница: 15 / 174

•

Using this Manual

Variable Wavelength Detectors (VC-D40, VF-D40)
Operating Manual

Page 15

1.3

Reference Documentation

In addition to this operating manual, other documentation is available
for reference.

Hardware Documentation

Additional hardware documentation includes the following:

•

Operating manuals

for the other modules of the Vanquish system

A printed version of the manual is shipped with the device.

•

Vanquish System Operating Manual

A printed version of the manual is shipped with the Vanquish system
base and solvent rack.

•

Instrument Installation Qualification Operating Instructions

TIP

Electronic versions of these manuals are available as PDF (Portable

Document Format) files. To open and read the PDF files, Adobe™
Reader™ or Adobe™ Acrobat™ is required.

Software Documentation

Additional software documentation includes the following:

•

Chromeleon™ Help and documents

The

Chromeleon Help

provides extensive information and

comprehensive reference material for all aspects of the software.

In addition, the following documentation is available (availability
depends on the software version):

•

Installation Guide

For basic information about device installation and configuration,
refer to the

Installation Guide

•

Instrument Configuration Manager Help

For specific information about a certain device, refer to the

Instrument Configuration Manager Help.

In Chromeleon 7, devices

are called modules.

•

Quick Start Guide

For information about the main elements of the user interface and
step-by-step guidance through the most important workflows, refer
to the

Quick Start Guide

•

Reference Card

For a concise overview of the most important workflows, refer to
the

Reference Card

Содержание Thermo Scientific Vanquish VC-D40















































































































































































Результаты поиска

Содержание Thermo Scientific Vanquish VC-D40

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Thermo Scientific Vanquish VC-D40, Руководство по эксплуатации

Результаты поиска

Содержание Thermo Scientific Vanquish VC-D40

Отзывы:

Бренды по названию

Популярные бренды