manualshive.com logo in svg

Thermo Scientific Thermo Scientific Vanquish VC-D40, Руководство по эксплуатации


Поделиться
Скачать
background image

2

 • 

Safety

Variable Wavelength Detectors (VC-D40, VF-D40) 
Operating Manual

Page 23

Gloves

To protect you from harmful liquids and avoid personal injury during
maintenance or service, put on appropriate protective gloves.

2.3.4

Electrical Safety Precautions

WARNING—Electric Shock or Damage to the Device

High voltages are present inside the device that could cause an electric
shock or damage to the device.

•

Do not make any changes to the electrical or grounding connections.

•

If you suspect any kind of electrical damage, disconnect the power
cord and contact Thermo Fisher Scientific Technical Support for
assistance.

•

Do not open the housing or remove protective panels unless
specifically instructed to do so in this manual.

•

Do not place liquid reservoirs directly upon the device. Liquid might
leak into the device and get into contact with electronic components
causing a short circuit. Instead, place liquid reservoirs in the solvent
rack that is available for the Vanquish system.

2.3.5

General Residual Hazards

Pay attention to the following general residual hazards when working
with the device:

Содержание Thermo Scientific Vanquish VC-D40















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Thermo Scientific Vanquish VC-D40

Samsung SMARTCAM SNH-1011N Quick Start Manual preview
SMARTCAM SNH-1011N
Бренд: Samsung Страницы: 2
Barnett Engineering ProTalk Cv3 Replacement Instructions preview
ProTalk Cv3
Бренд: Barnett Engineering Страницы: 3
Olympus nortec 600 User Manual preview
nortec 600
Бренд: Olympus Страницы: 374
Olympus EPOCH 6LT User Manual preview
EPOCH 6LT
Бренд: Olympus Страницы: 66
Ubiquiti airCam MINI User Manual preview
airCam MINI
Бренд: Ubiquiti Страницы: 31
Uniden UDR744 User Manual preview
UDR744
Бренд: Uniden Страницы: 32
Panasonic BB-HCM403A Getting Started preview
BB-HCM403A
Бренд: Panasonic Страницы: 4
ICON LevelPro ProScan 3 Series Operating Manual preview
LevelPro ProScan 3 Series
Бренд: ICON Страницы: 14
ICON Level pro 200C Series Operating Manual preview
Level pro 200C Series
Бренд: ICON Страницы: 19
Abus EasyLook PPDF17000 Operating Instructions Manual preview
EasyLook PPDF17000
Бренд: Abus Страницы: 23
i-PRO WV-S1536LNS Installation Manual preview
WV-S1536LNS
Бренд: i-PRO Страницы: 2
jablotron JA-83P Manual preview
JA-83P
Бренд: jablotron Страницы: 2
jablotron GS-133 Quick Start Manual preview
GS-133
Бренд: jablotron Страницы: 2
ATV B7T3I Instruction Manual preview
B7T3I
Бренд: ATV Страницы: 8
Zumimall GX2S Quick Start Manual preview
GX2S
Бренд: Zumimall Страницы: 28
KH SECURITY Backpack alarm User Manual preview
Backpack alarm
Бренд: KH SECURITY Страницы: 2
Dahua N51BI22 Quick Start Manual preview
N51BI22
Бренд: Dahua Страницы: 16
Super Circuits CCR-1 Quick Start Manual preview
CCR-1
Бренд: Super Circuits Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды