background image

 

Thermo Scientific

     

Multifuge X1R 

 

1-3

1

Introduction and description

Technical data

Technical data

The technical data of the Multifuge X1R  is listed in the following table. 

Table 1-1. 

Technical

 

Data

 

Multifuge X1R 

Feature

Environmental conditions

Multifuge X1R 

-Use in interior spaces

-Altitudes of up to 2,000

 

m above sea level

-

M

ax. relative humidity 80

 

% up to 31 °C; decreasing linearly up to 50

 

%

relative humidity at 40 °C.

Permissible ambient temperature 

+2 °C to +

3

5 °C

Overvoltage category

II

Pollution degree

2

Voltage

230 V

Heat dissipation

4778 BTU/h

IP

20

Run time

U

nlimited

Max speed n

max

15200 rpm (depending on the rotor)

Min speed n

min

300 rpm

Maximum RCF value at n

max

25830 x

 

Maximum kinetic energy

62.5 kJ

Noise level at maximum speed 

< 63 dB (A)

Temperature setting range

-10 °C to +40 °C

Dimensions

R

efrigerated

Height
Height with lid open
Width
Depth
Table top height

360 mm 
870 mm
623 mm 
605 mm
310 mm

Weight without rotor

91.5 kg

 

Refrigerant 

Quantity   Pressure  

GWP 

 CO2e 

Order No.

75004249

R-

134

A

0.

2

8 kg 

31 bar 

3922 

       

1.49 t 

Centrifuge

Thermo Scientific

 

Multifuge X1R 

Contains fluorinated greenhouse gases in a hermetically sealed system.

Refrigerant 

Содержание Multifuge X1R



























































Отзывы: